Stardust Satin Finish Sealers StarClean
Star System Products




Made In USA MTA, Inc.

Sealer for all types of marble, granite, stone, tile and masonry surfaces.

Product Description
Star Impregnator|ASF has been developed to perform with the same outstanding benefits and applications of the original Star Impregnator, without the environmental impact or vapor trails. Star Impregnator|ASF is an aqueous based, siloxane silicon, high solids formula that performs as the mineral based products which have been the standard in our industry. Star Impregnator|ASF penetrates into the pores of the surface to form a barrier that is resistant to moisture and stains while allowing complete vapor transmission. Star Impregnator|ASF is not a surface coating and will not alter the natural look. All surfaces are harder and less slippery. Star Impregnator|ASF can be used on interior and exterior applications from -20 F to +212 F. Star Impregnator|ASF allows maximum penetration while providing excellent coverage for cost effective performance. Star Impregnator|ASF averages five to twenty times the coverage of other products (See coverage chart below). Star Impregnator|ASF is U.V. transparent, resists acid rain and will not yellow under any circumstances. Star Impregnator|ASF inhibits the growth of mold, mildew and fungus in humid and damp areas. For added color on textured non-polished surfaces, Star Satin Finish may be applied after Impregnator|ASF has cured. See product data sheet on Satin Finish for proper application instructions. Due to the difference of each material, several inconspicuous test patches should be completed to assure maximum performance. User must determine suitability of the product for their intended use.

Porous Substrates
Absorption rates vary for each natural stone and man made product. Porosity and absorption are separate factors which are unique to each material. For materials identified as highly absorbent and /or very porous, test with 2 or 3 applications, affording proper cure time between applications. If further stain proofing is required, Triple Star Impregnator is recommended.

Applications Instructions

New Installation - Before Grouting
Apply Star Impregnator|ASF on all surfaces prior to grouting. This step will allow quick and easy clean up after grouting. Grout can stain many materials if this procedure is not used prior to grouting. Apply Star Impregnator|ASF using a clean cotton towel, lambs wool applicator, rayon mop or pneumatic sprayer. Apply enough to wet surface. (See coverage chart below) Be careful not to saturate the open grout joints. Allow Star Impregnator|ASF to stand for 3 to 5 minutes for maximum penetration. All excess must be removed at this time with a clean dry towel. This is especially important on glazed, polished and porcelain materials. Allow Star Impregnator|ASF to cure 24 hours before continuing with the grouting procedure.

New Installation - After Grouting
All excess grout residue/haze must be removed with the appropriate cleaner before continuing. Apply Star Impregnator|ASF to the grout joints using a paint brush or towel. On larger areas or more porous materials, a second application may be applied over the entire surface including the grout in the same manner as mentioned above. These procedures will protect the grout joint as well as the tile or stone surface.

Existing Installation
Remove all existing wax and topical matter with Starstrip or compatible stripping agent. If surface shows imbedded dirts or stains, refer to Starclean to restore face of surface. After allowing to thoroughly dry, apply Star Impregnator|ASF as directed above.

Cure Time
Star Impregnator|ASF fully cures in 24 hours. It will be dry to the touch in 30 minutes. Traffic is allowed after 8 hours. If humidity is a factor, adjust air conditioning/FVAC system to lowest humidity setting, or use air movers to hydrate product for accelerated cure time.

Star Impregnator|ASF should be stored in the original container, securely sealed to avoid contamination/leakage. Store at 40 F to 77 F (3 to 4C). Star Impregnator|ASF has a shelf life of 12 months. Extended shelf life requires shaking or stirring of product before application.

Environmental Impact
Star Impregnator|ASF exceeds all regulated criteria applicable, has no mineral vapor trail, no VOC content, is non corrosive and extended life biodegradable.

Coverage (square footage / gallon)
Sanded Grout
Quarry Tile
Glazed Tile
Porcelain Tile
Polished Granite
Polished Marble
Brick Pavers
250 - 1000
500 - 1500
1500 - 2500
2500 - 3500
2500 - 3500
2500 - 3500
1500 - 2500
500 - 1500
1500 - 1500
1500 - 2500

Available Quantities
Case (4) 1 gl. Containers
55 gl. Drum

Designed for environmentally safe preservation, maintenance & restoration of marble & all natural stone.