Stardust Satin Finish Sealers StarClean
PRODUCTS HOMEOWNERS PROFESSIONALS CONSULTING CONTACT US HOME
Star System Products

Qty:  

  

PayPal

Made In USA MTA, Inc.

Star Impregnator
Sealer for all types of marble, granite, stone, tile and masonry surfaces.

Product Description
Star Impregnator is a unique product designed for the protection of all grout, ceramic and quarry tile, marble, granite, slate, limestone, concrete, brick and masonry surfaces. Star Impregnator penetrates into the pores of the surface to form a barrier that is resistant to moisture and stains while allowing complete vapor transmission. Star Impregnator is not a surface coating and well not alter the natural look. All surfaces are harder and less slippery. Star Impregnator can be used on interior and exterior applications from -65 degrees F to +400 degrees F. Star impregnator allows maximum penetration while supplying maximum coverage for cost effective performance. Star Impregnator averages five to twenty times the coverage of other products (See coverage chart below). Star Impregnator is U.V. transparent, resists acid rain and will not yellow under any circumstances. Star Impregnator inhibits the growth of mold, mildew and fungus in humid and damp areas. For added color on textured non-polished surfaces. Star Satin Finish may be applied after Impregnator has cured. See product data sheet on Satin Finish for proper application instructions. Due to the difference of each material, several inconspicuous test patches should be completed to assure maximum performance. User must determine suitability of the product for their intended use.

Porous Substrates
Surface absorption can vary with various stone, tile, grout and paver products. With more porous materials such as limestone, flamed granite, saltillo, terra cotta, flagstone, sandstone, cantera and slate, Triple Star Impregnator is recommended for maximum protection form dirt, water grease and oils.

Applications Instructions

New Installation - Before Grouting
Apply Star Impregnator on all surfaces prior to grouting. This step will allow quick and easy cleanup after grouting. Grout can stain many materials if this procedure is not used prior to grouting. Apply Star Impregnator using a clean cotton towel, lambs wool applicator, rayon mop or pneumatic sprayer. Apply enough to wet surface. Be careful not to saturate the open grout joints. Allow Star Impregnator to stand for 3 to 5 minutes for maximum penetration. All excess must be removed at this time with clean dry towel. This is especially important on glazed and polished materials as well as all porcelain materials. Allow Star Impregnator to cure 24 hours before continuing with the grouting procedure.

New Installation - After Grouting
All excess grout residue/haze must be removed with the appropriate cleaner before continuing. Apply Star Impregnator to the grout joints using a paint brush or towel. On larger areas or more porous materials, a second application may be applied over the entire surface including the grout joint in the same manner as mentioned above. These procedures will protect the grout joint as well as the tile or stone surface.

Existing Installation
Remove any existing wax, coating or other sealers with Starstrip or appropriate stripper. Clean the surface and grout with Starclean per the instructions. Apply Star Impregnator as directed.

Coverage (square footage / gallon)
Sanded Grout
Quarry Tile
Ceramic Tile
Glazed Tile
Porcelain Tile
Polished Granite
Polished Marble
Terrazzo
750 - 1500
1000 - 2000
2000 - 3000
2000 - 3000
3000 - 4000
3000 - 4000
3000 - 4000
2000 - 3000
Brick
Concrete
Stucco
Slate
Quartz
Travertine
Masonry
1000 - 2000
500 - 1500
750 - 1500
1000 - 2000
2000 - 3000
2000 - 3000
1000 - 2000

Available Quantities
Case (12) 1qt. Containers
Case (4) 1 gl. Containers
55 gl. Drum
 

<< RETURN